Category

  • Offers

    • Easy payment

    Bezahlung

    Catalogue » Product and care instructions

    Product and care instructions

    PRODUCT AND CARE


    Indoor furniture

    Our wooden furniture for indoor use are usually made from solid beech. The surface is stained and varnished. We use only environmentally friendly and water-soluble stains and paints that meet the latest environmental standards.

    Color differences, we must explicitly due to the different textures and colors of wood and processing technology excepted, as the individual models can be produced by different suppliers.

    Please do not put the furniture out of direct sunlight. Color changes caused by solar radiations are no grounds for complaint. Wood furniture, we supply raw must be possible before further processing surface again by ground completely due to the storage time.

    With a selection of wooden chairs and barstools, we provide a 4-year warranty on the strength of the frame. This is possible because the respective chairs and bar stools with proven, traditional technique, the predominant use of manual labor by trained personnel are made. The frames are mortised and glued and screwed with some models even further. They are basically fully assembled.

    This 4-year warranty on the strength of the frame is the use of appropriate use of these chairs or bar stools, the prevention of improper use or an above-average stress, and requires the attention of this product and care instructions .

    This particularly includes the regular checking of the gland (if present), especially at the beginning of the use and the tightening of this screw connection after 8 weeks of use, and then again after 6 months. We also recommend the use of floor glides to reduce the braking effect of the wood in some floor coverings.

    Some seats have roles. Please update to install, with no metal hammer, but should be pressed, or be tapped gently with a rubber mallet so that it can not be damaged.




    The services we bentwood furniture are manufactured with proven technology of classic furniture with a long manufacturing tradition. Bentwood is bent over hot water, steam, and then clamped into metal molds and dried. A design feature of bentwood furniture, which guarantees a high load stability - are the bolts in the individual bent chair parts, who can work flexibly, without breaking.


    The wood is a living material that works and therefore it is normal when the chairs unencumbered wiggle a bit. If the loaded chair, kick up your legs and back of the chair is stable and straight.

    Please check the glands and drag it to this if necessary, with the over-tightening the screws should be avoided. The unions have, especially at the beginning of the use, to be checked repeatedly because bentwood respond initially to the seating load. It is advisable to connect screws after 8 weeks of use, and then again tightened after about 6 months.

    Depending on soil conditions, the models must be provided by you with sliders, so that the braking effect of the wood is reduced to the flooring. The corresponding slides we offer you. Wet soils can also attack the stain of tables and chairs and cause discoloration. If you use felt pads, so they pay attention to the wear and tear. Worn glides can permanently damage the floor.
    Compared to traditional wood furniture is important to make sure that this never wet, but only with a cloth can be cleaned without the addition of maintenance products.
    The area must be immediately rubbed dry, otherwise it may cause paint damage. With real wood veneer panels, it can also cause swelling, or other detachment of the veneer. Wet clothes, umbrellas, etc., may not be placed on wood furniture, as well as the moisture can cause damage.


    When use of table tops with real wood veneer or solid wood Make sure that no sharp objects (glasses, ashtrays, candlesticks, etc.) be parked without a coaster on them, because scratching the clearcoat paint can.

    Chairs may not be aufgestuhlt on freshly wiped countertops. When maintaining this table is particularly important to ensure that this never wet wet, but only with a cloth can be cleaned without the addition of maintenance products. The area must be immediately rubbed dry, otherwise it may cause paint damage.

    The specified own fabric for upholstery only applies to small and plain-colored patterned fabrics, a fabric width of 140 cm. For the quality of submitted customer fabrics, we can assume no liability. For flat tissues is the right side of the substance to be labeled.

    Observed when care of materials , which were used as reference material for upholstery, to the notes, at the particular type of material in the catalog or on our website.

    If your furniture with leatherette (imitation leather) are made, then we recommend regular cleaning with special leather cleaners, avoiding the use of solvents and abrasive products. A cleaning with clear water is not sufficient. Our offered genuine leather comes from European raw and processed according to EU standards. Leather is a durable product of nature. However, by usage, sweat, sunlight, moisture, etc. The leather is dirty and dries out. In order to preserve the beauty and the natural protective function of leather, regular care is necessary.

    Leather upholstered seating should not be exposed to direct sunlight or be near the heater - the leather fades quickly, becomes brittle and brittle.

    Wet leather to dry slowly at room temperature - first with towels may express something. Particularly daily used leather furniture should be impregnated and nurtured so that they remain supple and retain its fresh appearance. Therefore care products containing wool fat (lanolin) - oils or waxes - too preserve the suppleness. The care must be tailored to the type of leather, so it is smooth and suede for each different product. For our furniture we use leather.

    In case of visible contamination should be cleaned with a mild leather cleaner. Be preserved, depending on use, the leather every 3 to 6 months with a foster milk.

    Discolouration of leather coverings on light have increased in recent years. In such leathers, we recommend regular treatment of the contact surfaces with a leather seal. This prevents the discolouration move in too deep. Previously clean
    The compatibility of care agents should always be pre-tested on an inconspicuous area.

     

    Table and table bases (except folding tables) are always sent disassembled and must be installed by the customer. All table frames can be combined with all the tops from our program (exceptions: aluminum frames with slabs of stone or glass panels with table racks without receptacle provided for systems). For foreign products, we make no guarantee. Self-assembly of table bases and tops must be properly made on the basis of our installation instructions and notes. Please note to ensure the maximum table size for each table bases around the state and steadiness in normal use. Einsäulengestelle are in principle not to plaque formation.

    When the mounting plates on the table, table bases according to installation instructions important to make sure that the table is dropped on a soft surface to prevent damage on the top of the table is not created.
    Our granite slabs are provided with an MDF lower plate as a direct attachment of the granite table top with the table frame is not possible.

    The services we office chairs and office chairs have a safety gas lift for seat height adjustment.
    Attention! Work and exchange at the gas springs may be performed only by trained personnel.
    The swivel chairs are fitted with castors for carpet (black) fitted according to DIN EN 12529.
    For use on hard floors, these roles for security against "soft" roles are exchanged (with the colored races).


    For certain cantilever chairs made of tubular steel is provided a stall, which is in the bag assembly and necessarily should be attached before the first use, thus tilting the chair will be avoided to the front. With some cantilever (eg, model TAPE) it is necessary to be tightened regularly existing metal brace under the seat and the screw according to the notice on our site.


    Other cantilever, which have a seat cover out of wood (VIENNA) are to be installed only in accordance with the Installation and /or notice on our site (for each product). The lack of mounting holes in the wood is no shortage. The wood screws can be screwed in without pilot holes. Not all pre-drilled holes in the wooden parts are intended for installation. Some serve as a receptacle for the painting process.



    Outdoor furniture



    		 Our furniture for outdoor use are made of either aluminum, stainless steel, plastic, steel or cast iron or steel pipe in combination with different plastic materials, or wood. Please note the hints that the furniture is fully weatherproof and suitable only for the covered outdoor area are.
    The aluminum furniture are light but stable, easy to stack and completely weatherproof. The anodized, polished or powder-coated surface of the aluminum tubes ensures a long service life. Only in indoor pools, the surface by chlorine disinfectant and sharp attack.


    Some items have a fully braided aluminum structure . The materials are tear resistant and UV resistant. Clean it only with the furniture (soap) and water, please use the Avoid chemical cleaning agents. This also applies to chairs with Polyesthergewebe, which is characterized by a high tensile strength and weather and UV resistance. This fabric care because of their tissue structure for rapid drying. One treatment prevents fungus.

    Furniture is made of stainless steel very durable, weatherproof and easy to clean, but also prone to scratches and stains. Stains remain on the smooth surface not liable and can be easily removed. Stainless steel also offers a bad micro-organisms flourish. General Care offers itself for example a damp cloth (preferably microfiber cloth) with all-purpose cleaner or stainless steel cleaner. Then wipe dry with a lint-free cloth. For cleaning in between is also quite window cleaners, grease pollution helps a normal detergent. Stainless steel should be even more polluted then please do not with scouring powder or steel wool rub. Thus, the protective layer of stainless steel is damaged, the worst case remain deep grooves or scratches. Rather give the cleaner on a cloth and cover the contaminated site and let soak. Then wipe again wet and dry rub. Also please do not put on the stainless steel wool as air or rust can be deposited on the stainless steel and is then difficult to remove. Can have an equally unpleasant spilled salt. It can be combined with liquid form hydrochloric acid which then eats tiny holes in the stainless steel.



    Some models for outdoor use, we offer Teak black locust wood or Asian oak to. This teak furniture and teak table tops and furniture with Asian and black locust wood oak are usually left untreated. To preserve the natural character and protection from the weather, the models must be treated prior to first use a  care oil. Without regular oil treatment are the wood teak and acacia wood a silvery patina and its surface becomes rough and brittle. The durability of tropical hardwoods is an oil treatment but independent. Asian furniture made of oak are to be treated periodically with a care in each case, oil, since this may be damaged by moisture.


    The table tops made of stainless steel (stainless-steel tabletops) consist of an MDF core, which is not waterproof. When used outdoors, therefore, all holes are sealed with silicone, so that no water can penetrate and not the MDF core swells. The tops should only be used in the covered area. In principle, tables outdoors are not stored "upside down" because the water because of the commonly used edge shape of the tables does not can proceed.
    Parse Time: 0.069s